User Tools
milestones_and_schedule
Differences
This shows you the differences between two versions of the page.
|
milestones_and_schedule [2014/01/21 09:06] hutch |
milestones_and_schedule [2014/03/17 14:03] (current) schultz |
||
|---|---|---|---|
| Line 17: | Line 17: | ||
| - Pass/fail | - Pass/fail | ||
| - | - [[Milestone 1]] | + | ====== Milestones ====== |
| - | - [[Milestone 2]] | + | |
| - | - [[Milestone 3]] | + | |
| + | [[Milestone 1]] | ||
| - | ====== Milestone 1A ====== | + | [[Milestone 2]] |
| - | {{:m1a.jpg|600}} | + | |
| - | * Objective: Demonstrate the operation of A/D and D/A | + | |
| - | * Configuration/inputs | + | |
| - | - Function generator (FG) connected to A/D PMOD | + | |
| - | - FG signal: 𝑉_1=1.5+0.05sin(2π 38E3 t) | + | |
| - | - Oscilloscope (OSC) connected to D/A PMOD | + | |
| - | - ZED board/software must sample the input and generate the output at 100 kHz. | + | |
| - | * Pass off requirement | + | |
| - | - 𝑉_2= 1.5+0.05sin(2π 38E3 t) | + | |
| - | ====== Milestone 1B ====== | + | [[Milestone 3]] |
| - | {{:m1b.jpg|600}} | + | |
| - | * Objective: Demonstrate the operation of analog boards | + | |
| - | * Configuration/inputs | + | |
| - | - Function generator (FG) connected to transmitter board | + | |
| - | - FG signal: 𝑉_1=0.5+0.5sin(2π 38E3 t) | + | |
| - | - LED and photodiode separated by 20’ | + | |
| - | - Oscilloscope (OSC) connected to receiver board | + | |
| - | * Pass off requirements | + | |
| - | - AC amplitude of V2>20 mV | + | |
| - | - Frequency of V2 = 38 kHz | + | |
| - | - Accomplished using FFT math function of the oscilloscope | + | |
| - | + | ||
| - | + | ||
| - | ====== Milestone 2A ====== | + | |
| - | {{:m2a.jpg?600|}} | + | |
| - | + | ||
| - | * Objective: Demonstrate the operation of signal processing algorithm | + | |
| - | * Configuration/inputs | + | |
| - | - Function generator (FG) connected to A/D PMOD | + | |
| - | - FG signal: 𝑉_1=1.5+0.05sin(2π f t) | + | |
| - | - f is 22, 24, 26, 28, 30, 32, 34, 36, or 38 kHz | + | |
| - | * Pass requirements | + | |
| - | - ZED outputs frequency to a terminal | + | |
| - | - Output frequency matches the input | + | |
| - | + | ||
| - | ====== Milestone 2B ====== | + | |
| - | {{:m2b.jpg?600|}} | + | |
| - | + | ||
| - | * Objective: Demonstrate the connection between ZED board and analog boards | + | |
| - | * Configuration/inputs | + | |
| - | - ZED board outputs 𝑉_1=.5+0.5sin(2π f t) | + | |
| - | - f is 22, 24, 26, 28, 30, 32, 34, 36, or 38 kHz | + | |
| - | - LED and photodiode separated by 20' | + | |
| - | * Pass requirements | + | |
| - | - AC amplitude of V2>20 mV | + | |
| - | - Frequency of V2 matches selected input frequency | + | |
| - | - Accomplished using FFT math function of the oscilloscope | + | |
| + | [[Milestone 4]] | ||
milestones_and_schedule.1390320407.txt.gz · Last modified: 2014/01/21 09:06 by hutch
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 3.0 Unported
